NE56604-42D Просмотр технического описания (PDF) - Philips Electronics

Номер в каталоге

Компоненты Описание

производитель

NE56604-42D

System reset with built-in Watchdog timer

Philips Electronics 

Philips Semiconductors

System reset with built-in Watchdog timer

Product data

NE56604-42

AC ELECTRICAL CHARACTERISTICS

Characteristics measured with VCC = 5.0 V, and Tamb = 25 °C, unless otherwise specified.

See Figure 27 (Test circuit 2) for test configuration used for AC parameters.

SYMBOL

PARAMETER

CONDITIONS

MIN. TYP. MAX. UNIT

tP1

Minimum power supply pulse width for

4.0 V ≤ negative-going VCC pulse ≤ 5.0 V

8.0

–

–

µs

detection

tCLKW

Clock input pulse width

3.0

–

–

µs

tCLK

Clock input cycle

20

–

–

µs

tWDM

Watchdog monitoring time (Notes 1, 6)

CT = 0.1 µF; RCT = open

50

100

150

ms

tWDR

Watchdog reset time (Notes 2, 6)

CT = 0.1 µF

1.0

2.0

3.0

ms

tPR

Power-on reset delay time (Notes 3, 6)

VCC = rising from 0 V; CT = 0.1 µF

50

100

150

ms

tPD1

Reset propagation delay time (Note 4)

RESET: RL1 = 2.2 kΩ; CL1 = 100 pF

–

2.0

10

µs

tPD2

RESET: RL2 = 10 kΩ; CL2 = 20 pF

–

3.0

10

µs

tR1

Reset rise time (Note 5)

RESET: RL1 = 2.2 kΩ; CL1 = 100 pF

–

1.0

1.5

µs

tR2

RESET: RL2 = 10 kΩ; CL2 = 20 pF

–

1.0

1.5

µs

tF1

Reset fall time (Note 5)

RESET: RL1 = 2.2 kΩ; CL1 = 100 pF

–

0.1

0.5

µs

tF2

RESET: RL2 = 10 kΩ; CL2 = 20 pF

–

0.5

1.0

µs

NOTES:

1. ‘Watchdog monitoring time’ is the duration from the last pulse (negative-going edge) of the timer clear clock pulse until reset output pulse

occurs (see Figure 20). A reset signal is output if a clock pulse is not input during this time. Watchdog monitoring time can be modified by

changing the value of the RCT pull-up resistor. Monitoring time adjustments are shown in Figure 25.

2. ‘Watchdog reset time’ is the reset pulse width (see Figure 20).

3. ‘Power-on reset delay time’ is the duration measured from the time VCC exceeds the upper detection threshold (VSH) and power-on reset

release is experienced (RESET output HIGH; RESET output LOW).

4. ‘Reset response time’ is the duration from when the supply voltage sags below the lower detection threshold (VSL) and reset occurs (RESET

output LOW, RESET output HIGH).

5. Reset rise and fall times are measured at 10% and 90% output levels.

6. Watchdog monitoring time (tWDM), Watchdog reset time (tWDR), and power-on reset delay time (tPR) during power-on can be modified by

varying the CT capacitance. The times can be approximated by applying the following formula. The recommended range for CT is 0.001 µF

to 10 µF.

Formula 1.

Calculation for approximate tPR, tWDM, and tWDR values:

tPR (ms) ≈ 1000 × CT (µF)

tWDM (ms) ≈ 1000 × CT (µF)

tWDR (ms) ≈ 20 × CT (µF)

Example:

When CT = 0.1 µF and RCT = open:

tPR ≈ 100 ms

tWDM ≈ 100 ms

tWDR ≈ 2.0 ms

2003 Oct 15

5

Share Link: