ADV476KP50 Просмотр технического описания (PDF) - Analog Devices
Номер в каталоге
Компоненты Описание
производитель
ADV476KP50 Datasheet PDF : 12 Pages
| |||
ADV476
Frame Buffer Interface
The P0-P7 inputs are used to address the color palette RAM, as
shown in Table IV. These inputs are latched on the rising edge
of PCLK and address any of the 256 locations in the color pal-
ette RAM. The addressed location contains 18 bits of color (6
bits of red, 6 bits of green and 6 bits of blue) information. This
data is transferred to the three DACs and is then converted to
an analog output (RED, GREEN, BLUE), these outputs then
control the red, green and blue electron guns in the monitor.
The BLANK input is also latched on the rising edge of PCLK.
This is to maintain synchronization with the color data.
buffer or the color palette RAM. The effect of this operation is
to partition the color palette into a user determined number of
color planes. This process can be used for special effects includ-
ing animation, overlays and flashing objects.
(See also application note entitled “Animation Using the Pixel
Read Mask Register of the ADV47x Series of Video RAM-
DACs,” available from Analog Devices (Pub No.
E1316–15–10/89).
Table IV. Pixel Select/Color Palette Control Truth Table
P0–P7
Addressed by Frame Buffer
00H
01H
•
•
FFH
Color Palette RAM Location 00H
Color Palette RAM Location 01H
••
••
Color Palette RAM Location FFH
Pixel Read Mask Register
The Pixel Read Mask Register in the ADV476 can be used to
implement register level pixel processing, thereby cutting down
on software overhead. This is achieved by gating the input pixel
stream (P0–P7) with the contents of the pixel read mask regis-
ter. The operation is a bitwise logical ANDing of the pixel data.
The contents of This register can be accessed and altered at any
time by the MPU (D0–D7). Table I shows the relevant control
signals.
This pixel masking operation can be used to alter the displayed
colors without changing the contents of either the video frame
Figure 3. Block Diagram Showing Pixel Read
Mask Register
Analog Interface
The ADV476 has three analog outputs, corresponding to the
Red, Green and Blue video signals.
The Red, Green and Blue analog outputs of the ADV476 are
high impedance current sources. Each one of these three RGB
current outputs is capable of directly driving a 37.5 Ω load, such
as a doubly-terminated 75 Ω coaxial cable. Figure 4a shows the
required configuration for each of the three RGB outputs con-
nected into a doubly-terminated 75 Ω load. This arrangement
will develop RS-343A video output voltage levels across a 75 Ω
monitor. A simple method of driving RS-170 video levels into a
75 Ω monitor is shown in Figure 4b. The output current levels
of the DACs remain unchanged but the source termination
resistance, ZS on each of the three DACs is increased from 75 Ω
to 150 Ω.
More detailed information regarding load terminations for vari-
ous output configurations, including RS-343A and RS-170, is
available in an application note entitled “Video Formats &
Required Load Terminations,” available from Analog Devices.
Figure 5 shows the video waveforms associated with the three
RGB outputs, driving the doubly terminated 75 Ω load of Fig-
ure 4a. The BLANK control input drives the analog outputs to
the Black Level. BLANK is asserted prior to horizontal and ver-
tical screen retrace. Table V details how the BLANK input
modifies the output levels.
Figure 4a. Recommended Analog Output Termination
for RS-343A
Figure 4b. Recommended Analog Output Termination
for RS-170
REV. B
–7–
Share Link: 