HSP45102SC-33Z(2005) Просмотр технического описания (PDF) - Intersil
Номер в каталоге
Компоненты Описание
производитель
HSP45102SC-33Z Datasheet PDF : 7 Pages
| |||
HSP45102
P0-1
ENPHAC
TXFR
LOAD
CLK
4-DLY
R
E
G
SD
SCLK
SFTEN
MSB/ LSB
SEL_L / M
R.P0-1
R.ENPHAC
R.TXFR
R
CLK
E
G
PHASE OFFSET ADDER A
R.P0-1 D
D
13 MSBs E
R
13
/
E
CLK G
13
/
R
E
G
SINE
ROM
/
R
R.LOAD
32
/
‘0’ / 32
/ 32
12
/
CLK
2-DLY
R
E
G
OUT0-11
FREQUENCY
CONTROL
SECTION
64-BIT / 32
SHIFT 32
REG /
FRCTRL
0-31
FRCTRL
32-63
R.LOAD
A
D
ACCUMULATOR D
INPUT
E
REGISTER
R
/ 32
R.TXFR
CLK
R
E / 32
G
/ 32
R.ENPHAC
CLK
R / 32
E
G
(HIGH SELECTS FRCTRL0-31, LOW SELECTS FRCTRL32-63)
PHASE ACCUMULATOR
FIGURE 1. NCO-12 FUNCTIONAL BLOCK DIAGRAM
Functional Description
The NCO12 produces a 12-bit sinusoid whose frequency
and phase are digitally controlled. The frequency of the sine
wave is determined by one of two 32-bit words. Selection of
the active word is made by SEL_L/M. The phase of the
output is controlled by the two-bit input P0-1, which is used
to select a phase offset of 0, 90, 180, or 270 degrees.
As shown in the Block Diagram, the NCO12 consists of a
Frequency Control Section, a Phase Accumulator, a Phase
Offset Adder and a Sine ROM. The Frequency Control
section serially loads the frequency control word into the
frequency register. The Phase Accumulator and Phase
Offset Adder compute the phase angle using the frequency
control word and the two phase modulation inputs. The Sine
ROM generates the sine of the computed phase angle. The
format of the 12-bit output is offset binary.
Frequency Control Section
The Frequency Control Section shown in Figure 1 serially
loads the frequency data into a 64-bit, bidirectional shift
register. The shift direction is selected with the MSB/LSB
input. When this input is high, the frequency control word on
the SD input is shifted into the register MSB first. When
MSB/LSB is low the data is shifted in LSB first. The register
shifts on the rising edge of SCLK when SFTEN is low. The
timing of these signals is shown in Figures 2A and 2B.
The 64 bits of the frequency register are sent to the Phase
Accumulator Section where 32 bits are selected to control
the frequency of the sinusoidal output.
Phase Accumulator Section
The phase accumulator and phase offset adder compute the
phase of the sine wave from the frequency control word and
the phase modulation bits P0-1. The architecture is shown in
Figure 1. The most significant 13 bits of the 32-bit phase
accumulator are summed with the two-bit phase offset to
generate the 13-bit phase input to the Sine Rom. A value of
0 corresponds to 0o, a value of 1000 hexadecimal
corresponds to a value of 180o.
The phase accumulator advances the phase by the amount
programmed into the frequency control register. The output
frequency is equal to:
FLO = (N × FCLK ⁄ 232), or
(EQ. 1)
N
=
INT
-FF---O-C----UL---K-T--
232
,
(EQ. 2)
where N is the 32 bits of frequency control word that is
programmed. INT[•] is the integer of the computation. For
example, if the control word is 20000000 hexadecimal and the
clock frequency is 30MHz, then the output frequency would be
FCLK/8, or 3.75MHz.
The frequency control multiplexer selects the least significant
32 bits from the 64-bit frequency control register when
SEL_L/M is high, and the most significant 32 bits when
SEL_L/M is low. When only one frequency word is desired,
SEL_L/M and MSB/LSB must be either both high or both
low. This is due to the fact that when a frequency control
word is loaded into the shift register LSB first, it enters
through the most significant bit of the register. After 32 bits
have been shifted in, they will reside in the 32 most
significant bits of the 64-bit register.
When TXFR is asserted, the 32 bits selected by the frequency
control multiplexer are clocked into the phase accumulator input
3
Share Link: 