ISL6140 Просмотр технического описания (PDF) - Renesas Electronics
Номер в каталоге
Компоненты Описание
производитель
ISL6140 Datasheet PDF : 20 Pages
| |||
ISL6140, ISL6150
Electrical Specifications
VDD = +48V, VEE = +0V Unless Otherwise Specified. All tests are over the full temperature
range; either Commercial (0°C to +70°C) or Industrial (-40°C to +85°C). Typical specs are
at +25°C. Boldface limits apply over the operating temperature range, -40°C to
+85°C. (Continued)
PARAMETER
SYMBOL
TEST
CONDITIONS
PART NUMBER
TEST
OR GRADE
LEVEL OR MIN
MAX
NOTES (Note 7) TYP (Note 7) UNITS
DRAIN PIN
Power Good Threshold (L to H)
VPGLH VDRAIN - VEE, Low to High
Transition
1.55 1.70 1.87
V
Power Good Threshold (H to L)
VPGHL VDRAIN - VEE, High to Low
Transition
1.10 1.25 1.42
V
Power Good Threshold Hysteresis
VPGHY
Drain Input Bias Current
IDRAIN
ISL6140 (PWRGD PIN: L VERSION)
VDRAIN = 48V
0.30 0.45 0.60
V
10
35
60
µA
PWRGD Output Low Voltage
VOL
Output Leakage
IOH
ISL6150 (PWRGD PIN: H VERSION)
(VDRAIN - VEE) < VPG
IOUT = 1mA
IOUT = 3mA
IOUT = 5mA
VDRAIN = 48V, VPWRGD = 80V
-
0.28 0.50
V
-
0.88 1.20
-
1.45 1.95
V
-
0.05
10
µA
PWRGD Output Low Voltage
(PWRGD-DRAIN)
VOL
VDRAIN = 5V, IOUT = 1mA
-
0.80 1.0
V
PWRGD Output Impedance
AC TIMING
ROUT (VDRAIN - VEE) < VPG
3.5
6.2
9.0
k
OV High to GATE Low
OV Low to GATE High
UV Low to GATE Low
UV High to GATE High
SENSE High to GATE Low
ISL6140 (L VERSION)
tPHLOV (Figures 1, 3A)
tPLHOV (Figures 1, 3A)
tPHLUV (Figures 1, 3B)
tPLHUV (Figures 1, 3B)
tPHLSENSE (Figures 1, 2)
0.6
1.6
3.0
µs
1.0
7.8 12.0
µs
0.6
1.3
3.0
µs
1.0
8.4 12.0
µs
2
3
4
µs
DRAIN Low to PWRGD Low
DRAIN High to PWRGD High
ISL6150 (H VERSION)
tPHLPG
tPLHPG
(Figures 1, 4A)
(Figures 1, 4A)
0.1
0.9
2.0
µs
0.1
0.7
2.0
µs
DRAIN Low to (PWRGD-DRAIN)
High
tPHLPG (Figures 1, 4B)
6
0.1
0.9
2.0
µs
DRAIN High to (PWRGD-DRAIN)
Low
tPLHPG (Figures 1, 4B)
6
0.1
0.8
2.0
µs
NOTES:
5. Typical value depends on VDD voltage; see Figure 13, “VGATE vs VDD” (<20V).
6. PWRGD is referenced to DRAIN; VPWRGD-VDRAIN = 0V.
7. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established
by characterization and are not production tested.
FN9039 Rev 5.00
December 3, 2015
Page 5 of 20
Share Link: 