H5009-5012 Просмотр технического описания (PDF) - Intersil
Номер в каталоге
Компоненты Описание
производитель
H5009-5012 Datasheet PDF : 3 Pages
| |||
IH5009 Series
Absolute Maximum Ratings
Positive Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
Negative Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . .-15V
Diode Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
Power Dissipation (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW
Thermal Information
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
Operating Conditions
Temperature Range
5009C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
5009M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: Dissipation rating assumes device is mounted with all leads welded or soldered to printed circuit board in ambient temperature below
75oC. For higher temperature, derate at rate of 5m/WoC.
Electrical Specifications (Per Channel)
PARAMETER
(NOTE 1)
SYMBOL
(NOTE 4)
TEST
CONDITIONS
(NOTE 2)
TYPE
-55oC (M)
0oC (C)
MIN/MAX
25oC
TYP MIN/MAX
125oC (M)
70oC (C)
MIN/MAX
UNITS
Input Current-ON
Input Current-OFF
Input Current-OFF
Channel Control
Voltage-ON
IIN(ON)
IIN(OFF)
ALL
5V Logic Ckts
IIN(OFF) 15V Logic Ckts
VIN(ON) 5V Logic Ckts
VIN = 0V, ID = 2mA
VIN = +4.5V,
VA = ±10V
VIN = +11V,
VA = ±10V
Note 3
-
0.01
±0.5
-
0.04
±0.5
-
0.04
±0.5
0.5
-
0.5
100
µA
20
nA
20
nA
0.5
V
Channel Control
Voltage-ON
VIN(ON) 15V Logic Ckts Note 3
1.5
-
1.5
1.5
V
Channel Control
Voltage-OFF
VIN(OFF) 5V Logic Ckts
Note 3
-
-
4.5
4.5
V
Channel Control
Voltage-OFF
VIN(OFF) 15V Logic Ckts Note 3
-
-
11.0
11.0
V
Leakage Current-OFF ID(OFF)
Leakage Current-OFF ID(OFF)
Leakage Current-ON ID(ON)
5V Logic Ckts
15V Logic Ckts
5V Logic Ckts
VIN = +4.5V,
VA = ±10V
VIN = +11V,
VA = ±10V
VIN = 0V, IS = 1mA
-
0.02
±0.5
20
nA
-
0.02
±0.5
20
nA
-
0.30
±1.0
1000 (M) nA
200 (C)
Leakage Current-ON ID(ON)
15V Logic Ckts VIN = 0V, IS = 1mA
-
0.10
±0.5
500 (M) nA
100 (C)
Leakage Current-ON ID(ON)
5V Logic Ckts
VIN = 0V, IS = 2mA
-
-
1.0
10
µA
Leakage Current-ON ID(ON)
15V Logic Ckts VIN = 0V, IS = 2mA
-
-
2.0
100
µA
Drain-Source
ON-Resistance
rDS(ON) 5V Logic Ckts
ID = 2mA, VIN = 0.5V
150
90
150
385 (M)
Ω
240 (C)
Drain-Source
ON-Resistance
rDS(ON) 15V Logic Ckts ID = 2mA, VIN = 1.5V
100
80
100
250 (M)
Ω
160 (C)
Turn-ON Time
Turn-OFF Time
Cross Talk
t(ON)
All
t(OFF)
All
CT
All
f = 100Hz
-
150
500
-
300
500
-
120
-
-
ns
-
ns
-
dB
NOTES:
1. (OFF) and (ON) subscript notation refers to the conduction state of the FET switch for the given test.
2. Refer to Figure 1 for definition of terms.
3. VIN(ON) and VIN(OFF) are test conditions guaranteed by the tests of rDS(ON) and ID(OFF) respectively.
4. “5V Logic CKTS” applies to even-numbered devices. “15V Logic CKTS” applies to odd-numbered devices.
4-3
Share Link: 