LA4636 Просмотр технического описания (PDF) - SANYO -> Panasonic
Номер в каталоге
Компоненты Описание
производитель
LA4636 Datasheet PDF : 3 Pages
| |||
LA4636
Standby Function
Pin 5 Equivalent Circuit Inside IC
Standby
Pin Voltage
VSTB
ISTB=500µA or less
5
RSTB
Approximately
15kΩ
1.4V
ILA00776
Pd max -- Ta
30
Infinite heat sink
25
20
AI heat sink
Mounting
torque 39N•cm
Flat washer
Silicone grease
applied
qjc=3°C / W
15
100 ¥ 100 ¥ 1.5 mm3
12.5
10
50 ¥ 50 ¥ 1.5 mm3
7
5 Single IC
3.2
0
--20 0
20 40 60 80 100 120 140 160
Ambient temperature, Ta – °C
ILA00777
The IC’s pin 5 is the standby pin, and the amplifier turns
on when approximately 2 V or more is applied to it.
If +5 V is applied directly to pin 5 the inflow current of
pin 5 is approximately 240 µA.
ISTB =
5 V – 1.4 V = 240 µA
15 kΩ
If the microprocessor is used, an external current limiting
resistor (RSTB) should be inserted if necessary (to reduce
the inflow current).
If a voltage other than that supplied by the microprocessor
is applied, the pin 5 inflow current should be limited to
500 µA or less using the applied VSTB value by calculating
RSTB using the following equation and inserting a resistor
if necessary.
RSTB =
Applied
Voltage (VSTB)
500 µA
–
1.4
V
–
15
kΩ
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification”
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of July, 2002. Specifications and information herein are subject to
change without notice.
PS No. 6985-3/3
Share Link: 