ADP3401 Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

производитель

ADP3401

GSM Power Management System

Analog Devices 

ADP3401

For the lowest ripple and best efficiency, use a 0.1 µF, ceramic

capacitor for the charge pump flying capacitor (CAP+ and CAP–).

A good quality dielectric, such as X7R is recommended.

Setting the Charger Turn-On Threshold

The ADP3401 can be turned on when the charger input exceeds

a programmable threshold voltage. The charger’s threshold and

hysteresis are set by selecting the values for R1 and R2 shown in

Figure 15.

The turn-on threshold for the charger is calculated using:

VCHR

=





R2

R2

+

×

RHYS

RHYS

×



R1



+ 1 ×VT



Where VT is the CHRON threshold voltage and RHYS is the

CHRON hysteresis resistance.

The hysteresis is determined using:

VHYS

=

VT

RHYS

× R1

Combining the above equations and solving for R1 and R2 gives

the following formulas:

R1 =

RHYS

VT

× VHYS

R2 =

R1 × RHYS

VVCHT R

−



1

× RHYS

− R1

Example: R1 = 10 kΩ and R2 = 30.2 kΩ gives a charger thresh-

old (not counting the drop in the power Schottky diode) of

3.5 V ± 160 mV with a 200 mV ± 30 mV hysteresis.

Charger Diode Selection

The diode shown in Figure 15 is used to prevent the battery from

discharging into the charger turn-on setting resistors, R1 and R2.

A Schottky diode is recommended to minimize the voltage differ-

ence from the charger to the battery and the power dissipation.

Choose a diode with a current rating high enough to handle both

the battery charging current and the current the ADP3401 will

draw if powered up during charging. The battery charging current

is dependent on the battery chemistry and the charger circuit.

The ADP3401 current will be dependent on the loading.

Printed Circuit Board Layout Considerations

Use the following general guidelines when designing printed

circuit boards:

1. Split the battery connection to the VBAT and SIMBAT

pins of the ADP3401. Use separate traces for each connection

and locate the input capacitors as close to the pins as possible.

2. SIM input and output capacitors should be returned to the

SIMGND and kept as close as possible to the ADP3401 to

minimize noise. Traces to the SIM charge pump capacitor

should be kept as short as possible to minimize noise.

3. VCCA and VTCXO capacitors should be returned to AGND.

4. VCC and VRTC capacitors should be returned to DGND.

5. Split the ground connections. Use separate traces or planes

for the analog, digital, and power grounds, and tie them

together at a single point, preferably close to the battery return.

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

28-Lead Thin Shrink Small Outline (TSSOP)

(RU-28A)

0.386 (9.80)

0.378 (9.60)

28

1

PIN 1

0.0374 (0.95)

0.0335 (0.85)

15

0.244 (6.20)

0.236 (6.00)

0.325 (8.25)

0.313 (7.95)

14

0.0433 (1.10)

MAX

0.006 (0.15) 0.0256

0.002 (0.05) (0.65)

BSC

0.0118 (0.30) SEATING

0.0075 (0.19) PLANE

8؇

0.0078 (0.200) 0؇

0.0035 (0.090)

0.030 (0.75)

0.020 (0.50)

–12–

REV. 0

Share Link: