M35049 Просмотр технического описания (PDF) - MITSUBISHI ELECTRIC
Номер в каталоге
Компоненты Описание
производитель
M35049 Datasheet PDF : 50 Pages
| |||
MITSUBISHI MICROCOMPUTERS
M35049-XXXFP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(7) Address 12616
DA Register
Status
Contents
Function
Remarks
0
LIN10
0
Vertical direction dot size setting for
The vertical dot size for line n in the character dot lines (18 vertical the 11th line.
1 lines) is set using LINn (n = 2 to 17).
0
1
LIN11
Dot size can be selected between 2 types for each dot line.
1
Vertical direction dot size setting for
the 11th line.
2
LIN12
0
For dot size, see the below registers. Line 1 and lines 2 to 12 can
be set independent of one another.
Vertical direction dot size setting for
the 12th line.
1
0
3
LIN13
1
0
4
LIN14
1
LINn = “0”
LINn = “1”
1st line
Refer to VSZ1L0 Refer to VSZ1H0
and VSZ1L1
and VSZ1H1
2nd to 12th Refer to VSZ2L0 Refer to VSZ2H0
line
and VSZ2L1
and VSZ2H1
Vertical direction dot size setting for
the 13th line.
Vertical direction dot size setting for
the 14th line.
0
5
LIN15
1
Vertical direction dot size setting for
the 15th line.
0
6
LIN16
1
Vertical direction dot size setting for
the 16th line.
0
7
LIN17
1
Vertical direction dot size setting for
the 17th line.
8
V18SZ0
0 H: Cycle with the horizontal synchronizing pulse
1
V18SZ1 V18SZ0 Vertical direction size
0
0
1H/dot
0
9
V18SZ1
0
1
1
0
2H/dot
3H/dot
1
1
1
4H/dot
Vertical direction dot size setting for
the 18th line.
(all lines are common)
0 H: Cycle with the horizontal synchronizing pulse
A
VSZ2L0
1
VSZ2L1 VSZ2L0 Vertical direction size
0
0
1H/dot
0
B
VSZ2L1
0
1
1
0
2H/dot
3H/dot
1
1
1
4H/dot
Character dot line vertical direction dot
size setting for the 2nd line to 12th line
(LINn = 0).
0 H: Cycle with the horizontal synchronizing pulse
C
VSZ2H0
1
VSZ2H1 VSZ2H0 Vertical direction size
0
0
1H/dot
0
D
VSZ2H1
1
0
1
1
0
1
1
2H/dot
3H/dot
4H/dot
Character dot line vertical direction dot
size setting for the 2nd line to 12th line
(LINn = 1).
E
POPUP
0 Page 1 priority display
(Note 3)
1 Page 0 priority display
Sets the priority page for when 2 pages are
displayed at the same time. The setting is
effective only when the standard display
mode is set as MODE0 = "0" , MODE1 = "0".
See "DISPLAY FORM 2" .
____
Notes 1. The mark around the status value means the reset status by the "L" level is input to AC pin.
2. The page in which data is written is controlled by the DAF bit. When set to "0", data is written into page 0, whereas when set to "1", data is written
into page 1.
3. Registers marked with (Note 3) are found only in page 0, therefore the register value does not change when the DAF bit is set to "1".
14
Share Link: 