[NORDIC]

Introduction
The nRF24L01+ is a single chip 2.4GHz transceiver with an embedded baseband protocol engine (Enhanced ShockBurst™), suitable for ultra low power wireless applications. The nRF24L01+ is designed for operation in the world wide ISM frequency band at 2.400 - 2.4835GHz.

Key Features
• Worldwide 2.4GHz ISM band operation
• 250kbps, 1Mbps and 2Mbps on air data rates
• Ultra low power operation
• 11.3mA TX at 0dBm output power
• 13.5mA RX at 2Mbps air data rate
• 900nA in power down
• 26µA in standby-I
• On chip voltage regulator
• 1.9 to 3.6V supply range
• Enhanced ShockBurst™
• Automatic packet handling
• Auto packet transaction handling
• 6 data pipe MultiCeiver™
• Drop-in compatibility with nRF24L01
• On-air compatible in 250kbps and 1Mbps with nRF2401A, nRF2402, nRF24E1 and nRF24E2
• Low cost BOM
• ±60ppm 16MHz crystal
• 5V tolerant inputs
• Compact 20-pin 4x4mm QFN package

Applications
• Wireless PC Peripherals
• Mouse, keyboards and remotes
• 3-in-1 desktop bundles
• Advanced Media center remote controls
• VoIP headsets
• Game controllers
• Sports watches and sensors
• RF remote controls for consumer electronics
• Home and commercial automation
• Ultra low power sensor networks
• Active RFID
• Asset tracking systems
• Toys

HIGH POWER SWITCHING USE

INSULATED PACKAGE

● ID(rms) ..........................................................300A

● VDSS...............................................................75V

● Insulated Type

● 6-elements in a pack

● NTC Thermistor inside

APPLICATION

AC motor control of forklift (battery power source), UPS

Typical Applications
 • Low power SMPS
 • DC servo drives
 • UPS

Features
• Compact design
• One screw mounting
• Heat transfer and isolation through direct copper bonded aluminium oxide ceramic (DCB)
• Trench technology
• Short internal connections and low inductance case

Typical Applications
• Low switched mode power supplies
• DC servo drives
• UPS

MOSFET MODULE

SF100BA50 is a isolated power MOSFET MODULE designed for fast swiching applications of high voltage and current. The mounting base of the MODULE is electrically isolated from semiconductor elements for simple heatsink construction.

● ID = 100A, VDSS = 500V
● Suitable for high speed switching applications.
● Low ON resistance.
● Wide Safe Operating Areas.
● trr ≤ 700ns

MOSFET MODULE

Typical Applications*
 • Low power SMPS
 • DC servo drives
 • UPS

MOSFET MODULE

SF100CB100 is a isolated power MOSFET MODULE designed for fast swiching applications of high voltage and current with a fast recovery diode（trr≦300ns） reverse connected. The mounting base of the MODULE is electrically isolated from semiconductor elements for simple heatsink construction.

● ID＝100A, VDSS＝1000V
● Suitable for high speed switching applications.
● Low ON resistance.
● Wide Safe Operating Areas.
● trr≦300ns fast recovery diode for free wheel

MOSFET MODULE Dual 140A /500V

FEATURES
* Dual MOS FETs Cascaded Circuit
* Prevented Body Diodes of MOSFETs by SBDs, and Ultra Fast Recovery Diodes Connected in Parallel
* 300KHz High Speed Switching Possible TYPICAL APPLICATIONS
* Power Supply for the Communications and the Induction Heating

Features
 • Compact design
 • One screw mounting
 • Heat transfer and isolation through direct copper bonded alumium oxide ceramic (DCB)
 • Trench technology
 • Short internal connections and low inductance case
 • Integrated PTC temperature sensor

Typical Applications
 • Low switched mode power supplies
 • DC servo drives
 • UPS